D 4378 03 inservice monitoring of mineral turbine oils for steam and gas turbines free download as pdf file. The degradation end point is that point in the history of a material when 75% of the specimens tested has a tensile elongation at break of 5% or less. Vat monitor standard webprint printed and bound get online access. A number in parentheses indicates the year of last. Procedures include broom cleaning, vacuum cleaning, air blast cleaning, water cleaning, detergent water cleaning, and steam cleaning. Clean surface per astm d4260, wet surface with clean water, et ch with 1015% muriatic acid solution at the rate of 1 gallon per 75 square feet, scrub with stiff brush, allow suffi cient time for scrubbing and until bubbling stops, if no bubbling occurs, surface is contaminated. Aci308 recommended practice for curing concrete3 3.
Refer to astm d4378 for guidance on sampling and testing. Analyses recommended for gas and steam turbine users. Bulletin 17 astm f1869 moisture testing astm f3010. The printed report then gives both the open cell % and the corrected open cell % values. Find combined cycle steam turbines related suppliers. The ultrafoam pycnometer programming provides a convenient way to automate this procedure. I am not sure if the suggestions here were based on hypothetical or real sea. The last approved version of this historical standard is referenced on.
Astm d4378 08, standard practice for inservice monitoring of mineral turbine oils for steam and gas turbines, astm international, west conshohocken, pa, 2008. In light of this and other research, the astm made two changes to moisture measurement industry standards. Standard test method for foaming characteristics of. Astmd4318 standard test methods for liquid limit, plastic. Astm c25 19 standard test methods for chemical analysis of limestone, quicklime, and hydrated lime. Astm toc section 00 index section 01 iron and steel products volume 01.
Astm d 3826 this method covers the determination of the degradation end point a brittle point for degradable pe pp films and sheeting less than 1. Astm c1797 17 standard specification for ground calcium carbonate and aggregate mineral fillers for use in hydraulic cement concrete. D 4258 practice for surface cleaning concrete for coating2 d 4285 test method for indicating oil or water in compressed air2 d 4541 test method for pulloff strength of coatings using portable adhesion testers2 2. Astm c706 standard specification for limestone for animal feed use.
Astm d4378, standard practice for inservice monitoring of mineral turbine oils for steam, gas, and combined cycle turbines, astm international, west conshohocken, pa, 20, back to top. Astmd4318 historical revision information standard test methods for liquid limit, plastic limit, and plasticity index of soils astmd4318 2010 edition superseded see the following. Purchase your copy of astm c706 as a pdf download or hard copy directly from the official bsi shop. Astm d4378 standard practice for inservice monitoring of mineral turbine oils for steam, gas, and combined cycle turbines. Laboratory tests for steam and gas turbine oils mobil. Standard practice for fluorescent uv exposure of plastics. Astm d2216, astm d4753, astm d6026 standard test method for determination of water content of soil by direct heating. Astm d437808, standard practice for inservice monitoring of mineral turbine oils for steam and gas turbines, astm international, west conshohocken, pa, 2008, back to top. Lubricating oil recommendations for gas turbines coast lubricants. Second, astm created the f2170 standard that recognized insitu relative humidity testing as an.
A number in parentheses indicates the year of last reapproval. In astm d6226, a corrected percentage of open cells is estimated by remeasuring the volume of a cube after sectioning into eight parts. D4378 practices for inservice monitoring of mineral. Experiences with astm d02 practices d4378 and d6224 for. All bsi british standards available online in electronic and print formats. American society for testing and materials reprinted from the. Laboratory tests for steam and gas turbine oils mobil serv. Astm c706 standard specification for limestone for. Table 1 lists recommended properties of new oil and include the astm test. Table 1 liquid systems for densitygradient tubes system. D4378 practices for in service monitoring of mineral. Astm 4304 type i and iii gb china 111202011, l tga, ltsa and ltgsb. Standard test methods for liquid limit, plastic limit, and.
Astm d4378 08 standard practice for inservice monitoring. Focus is on trend analysis and identification of high concentrations of wear metals and additives in the oilengine under study. Astm d4378 standard practice for inservice monitoring of mineral turbine oils for steam, gas and combined cycle turbines is another resource for recommendations regarding selecting testing for condition monitoring of inservice turbine oil. Standard practice for surface cleaning concrete for coating1 this standard is issued under the. First, it amended astm f1869 to remove the calcium chloride moisture test as a means of measuring lightweight concrete moisture. Astm e351 pdf download now astm e351 pdf read online these test methods are under the jurisdiction of astm committee e01 on analytical chemistry for metals, ores, and related materials and are the direct responsibility of subcommittee e01. Astm d4378, the standard practice for inservice monitoring of mineral turbine oils for steam and gas turbines is the recognized standard for determining. A623m standard specification for tin mill products, general requirements metric. Dwg number gek32568 rev h released 6620 page of 26. Standard test method for free water and particulate. However, the precision estimates given in section are based on using only liquid baths. Some oil analysis laboratories have recognized the need for more compre. Adopted and modeled from astm d 437808 together with focuslabs testing.
For the d63810 iv specimen, are you sure you have the fillet values 25mm and 14mm arent flipped. Brief description of oxobiodegradable plastics degradation. Practice for use of a dichromate dosimetry system, category. Lubricating oil analysis according to astm d5185 using the. The month of schedule 3 is the same month for the month 1 of schedule 4. Mineral turbine oils for steam, gas and combined cycle turbines is an other resource for. Astm d4378 standard practice for inservice monitoring of mineral turbine. Service monitoring of mineral turbine oils for steam and gas turbines is the recognized standard for determining the condition of turbine oils. Purchase your copy of astm d4378 as a pdf download or hard copy directly from the official bsi shop.
D 4378 03 inservice monitoring of mineral turbine oils for. D4176 04 reapproved 2009 standard test method for free water and particulate contamination in distillate fuels visual inspection procedures 1 this standard is issued under the. For annual book of astm standards volumeinformation,refertothestandardsdocumentsummarypageon theastm website. D4378 standard practice for inservice monitoring of mineral turbine oils for steam and gas. Astm d437808 standard practice for inservice monitoring of mineral turbine oils for steam and gas turbines astm d4380842006 standard test method for density of bentonitic slurries astm d438106 standard test method for sand content by volume of bentonitic slurries. Total acid number astm d664 rust test for st astm d664 foaming astm d892 iso particle count iso 4406 air release astm d3427 mpc astm d7843 demulsibility astm d1401 moisture astm d6304 d7546 insolubles astm d2273 metals astm d5185 flash point astm d92 turbine oil analyses source. Astm d4378 , standard practice for inservice monitoring of mineral turbine oils for steam, gas, and combined cycle turbines, astm international, west conshohocken, pa, 20. Refer to astm d4258 or astm d4259, rinse surface two or three times.